Gn protein expressed in plants for diagnosis of severe fever with thrombocytopenia syndrome virus.

Severe fever with thrombocytopenia syndrome virus (SFTSV) causes the highly fatal disease in humans. To facilitate diagnosis, the native form of subunit glycoprotein (Gn), a prime target for potential vaccines and therapies, was produced in Nicotiana benthamiana using a Bamboo mosaic virus-based vector system. By fusion with secretory signal tags, SSExt, derived from the extension protein, and the (SP)10 motif, the yield of the recombinant Gn (rGn) was remarkably increased to approximately 7 mg/kg infiltrated leaves. Ultimately, an rGn-based ELISA was successfully established for the detection of SFTSV-specific antibodies in serum samples from naturally infected monkeys. As validated with the reference method, the specificity and sensitivity of rGn-ELISA were 94% and 96%, respectively. In conclusion, utilizing well-suited fusion tags facilitates rGn production and purification in substantial quantities while preserving its antigenic properties. The rGn-ELISA, characterized by its commendable sensitivity and specificity could serve as a viable alternative diagnostic method for assessing SFTSV seroprevalence. KEY POINTS: • SFTSV Gn, fused with secretory signal tags, was expressed by the BaMV-based vector. • The plant fusion tags increased expression levels and eased the purification of rGn. • The rGn-ELISA was established and validated; its specificity and sensitivity > 94%.

A strong hydrogen bond bridging interface based on tannic acid for improving the performance of high-filled bamboo fibers/poly (butylene succinate-co-butylene adipate) (PBSA)biocomposites.

Natural plant fiber-reinforced bio-based polymer composites are widely attracting attention because of their economical, readily available, low carbon, and biodegradable, and showing promise in gradually replacing petroleum-based composites. Nevertheless, the fragile interfacial bonding between fiber and substrate hinders the progression of low-cost and abundant sustainable high-performance biocomposites. In this paper, a novel high-performance sustainable biocomposite was built by introducing a high density strong hydrogen-bonded bridging interface based on tannic acid (TA) between bamboo fibers (BFs) and PBSA. Through comprehensive analysis, this strategy endowed the biocomposites with better mechanical properties, thermal stability, dynamic thermo-mechanical properties and water resistance. The optimum performance of the composites was achieved when the TA concentration was 2 g/L. Tensile strength as well as modulus, flexural strength as well as modulus, and impact strength improved by 22 %, 10 %, 15 %, 35 %, and 25 % respectively. Additionally, the initial degradation temperature(Tonset) and maximum degradation temperature(Tmax) increased by 12.07 °C and 14.8 °C respectively. The maximum storage modulus(E'), room temperature E', and loss modulus(E")elevated by 199 %, 75 %, and 181 % respectively. Moreover, the water absorption rate decreased by 59 %. The strong hydrogen-bonded bridging interface serves as a novel model and theory for biocomposite interface engineering. At the same time, it offers a promising future for the development of high performance sustainable biocomposites with low cost and abundant biomass resources and contributes to their wide application in aerospace, automotive, biomedical and other field.

A PAM hydrogel surface-coated hydroponic bamboo evaporator with efficient thermal utilization for solar evaporation.

Solar-driven interfacial water purification emerges as a sustainable technology for seawater desalination and wastewater treatment to address the challenge of water scarcity. Currently, the energy losses via radiation and convection to surrounding environment minimize its energy efficiency. Therefore, it is necessary to develop strategies to minimize the heat losses for efficient water purification. Here, a novel evaporator was developed through the in situ gelation of PAM hydrogel on the surface carbonized hydroponic bamboo (PSC) to promote energy efficiency. The inherent porous and layered network structures of bamboo, in synergy with the functional hydration capacity of PAM hydrogel, facilitated adequate water transportation, while reducing evaporation enthalpy. The PAM hydrogel firmly covered on the photothermal layer surface effectively minimized the radiation and convection heat losses, while further harvesting those thermal energy that would otherwise dissipate into the surrounding environment. The reduced thermal conductivity of PSC served as a thermal insulator as well, obstructing heat transfer to bulk water and thus diminishing conduction losses. Consequently, the rational designed PSC could efficiently convert solar energy to purified water, leading to the evaporation of 2.09 kg m-2 h-1, the energy efficiency of 87.6 % under one sun irradiation, and yielding 9.6 kg m-2 fresh water over 11 h outdoor operation. Moreover, the PSC also performs excellent salt rejection, and long-term stability at outdoor experiment. These results demonstrated high and stable solar evaporation performance could be achieved if turning heat losses into a way of extra energy extraction to further enhance the evaporation performance. This strategy appears to be a promising strategy for effective thermal energy management and practical application.

A bamboo bHLH transcription factor PeRHL4 has dual functions in enhancing drought and phosphorus starvation tolerance.

ROOTHAIRLESS (RHL) is a typical type of basic helix-loop-helix (bHLH) transcription factor (TF), which has been reported to participate in various aspects of plant growth and in response to stress. However, the functions of RHL subfamily members in moso bamboo (Phyllostachys edulis) remain unknown. In this study, we identified 14 bHLH genes (PeRHL1-PeRHL14) in moso bamboo. Phylogenetic tree and conserved motif analyses showed that PeRHLs were clustered into three clades. The expression analysis suggested that PeRHL4 was co-expressed with PeTIP1-1 and PePHT1-1 in moso bamboo. Moreover, these three genes were all up-regulated in moso bamboo under drought stress and phosphate starvation. Y1H, DLR and EMSA assays demonstrated that PeRHL4 could activate the expression of PeTIP1-1 and PePHT1-1. Furthermore, overexpression of PeRHL4 could increase both drought and phosphate starvation tolerance in transgenic rice, in which the expression of OsTIPs and OsPHT1s was significantly improved, respectively. Overall, our results indicated that drought stress and phosphate starvation could induce the expression of PeRHL4, which in turn activated downstream genes involved in water and phosphate transport. Collectively, our findings reveal that PeRHL4 acting as a positive regulator contributes to enhancing the tolerance of moso bamboo under drought stress and phosphate starvation.

Sustainable high-strength and dimensionally stable composites through in situ regulation and reconstitution of bamboo-derived lignin and hemicellulose contents.

The development of modern construction and transportation industries demands increasingly high requirements for thin, lightweight, high-strength, and highly tough composite materials, such as metal carbides and concrete. Bamboo is a green, low-carbon, fast-growing, renewable, and biodegradable material with high strength and toughness. However, the density of its inner layer is low due to the functional gradient (the volume fraction of vascular bundles decreases from the outer layer to the inner layer), resulting in low performance, high compressibility, and significant amounts of bamboo waste. We utilized chemical and mechanical treatments of bamboo's low-density, low-strength inner layers to create lightweight, ultra-thin, high-strength, and high-toughness composites. The treatment included the partial removal of lignin and hemicellulose to alter the chemical components, followed by mechanical drying and hot pressing. The treated bamboo had 100.8 % higher tensile strength (150.35 MPa), 47.7 % higher flexural strength (97.67 MPa), and 132.0 % higher water resistance and was approximately 68.9 % thinner than the natural bamboo. The excellent physical and mechanical properties of the treated bamboo are attributed to the contraction of parenchyma cells during delignification, the interlocking due to the collapse of parenchyma cells during mechanical drying, and an increase in the density of hydrogen bonds between cellulose molecular chains during hot pressing. Our research provides a new strategy for obtaining sustainable, ultra-thin, lightweight, high-strength, and high-toughness composite materials from bamboo for construction and transportation applications.

The mechanism of solid acid-catalyzed bamboo sawdust liquefaction under polyol systems.

Solid acid catalysts are widely used in the field of biomass catalytic conversion owing to their advantages of low environmental pollution, easy separation and reusability. Nevertheless, there are relatively few studies on the mechanism of solid acid liquefaction for biomass. In this study, the effect of acid strength and acid amount of various solid acids on the liquefaction efficiency has been investigated using waste bamboo sawdust generated from the pulp and paper industry as the raw material. In addition, the physicochemical changes of cellulose, hemicellulose and lignin during the reaction process of bamboo sawdust have been studied, and the liquefaction mechanism of bamboo sawdust under the action of various solid acids has been concluded. As a result, the liquefaction efficiency of bamboo sawdust under the polyol system of PEG400/propanetriol is mainly related to the acid strength of the solid acid, and the greater the acid strength of the solid acid, the better the catalytic effect on the bamboo sawdust, in which the residual amount of bamboo sawdust liquefaction catalyzed by the SPA catalyst is only 17.72%. Noteworthy, the most difficult component to liquefy is the crystallization of natural cellulose I into cellulose II during the reaction process, which is the primary obstacle to the complete liquefaction of bamboo sawdust by solid acid. Overall, these findings are valuable for the high value utilization of waste bamboo sawdust in the pulp and paper industry, as well as the application of solid acid catalytic technology for biomass.

Effect of oxygen-containing functional group contents on sorption of lead ions by acrylate-functionalized hydrochar.

The surface functional groups of hydrochar are crucial to its surface properties, and their contents are strongly positively correlated with the adsorption performance. In this study, acrylate-functionalized hydrochar (AHC) with varying contents of O-containing functional groups (OFGs) was synthesized via hydrothermal carbonization (HTC) of bamboo, acrylic acid and an initiator, and then deprotonated with NaOH. The AHCs were analyzed by various characterization techniques. During HTC, the higher amount of acrylic acid added led to higher carbon, oxygen and carboxyl contents, and to the larger specific surface area and pore volume of AHC. The adsorption kinetics, isotherms, thermodynamic, ionic strength and pH effects of Pb(II) on AHC were studied. Adsorption isotherms and kinetics obeyed Langmuir and pseudo-second-order models, respectively, indicating adsorption is monolayer chemical process. The adsorptive ability was well linearly related to the OFG contents of AHC. When acrylic acid was added to 25 mL during HTC, the adsorbing ability of AHC over Pb(II) reached 193.90 mg g-1. Hence, direct HTC of acrylic acid, biomass and an initiator can prepare hydrochar with controllable OFG contents, which is a prospective adsorbent for treating metal cations.

Genome-wide identification and expression analysis of the HAK/KUP/KT gene family in Moso bamboo.

The K+ uptake permease/high-affinity K+/K+ transporter (KUP/HAK/KT) family is the most prominent group of potassium (K+) transporters, playing a key role in K+ uptake, transport, plant growth and development, and stress tolerance. However, the presence and functions of the KUP/HAK/KT family in Moso bamboo (Phyllostachys edulis (Carriere) J. Houzeau), the fastest-growing plant, have not been studied. In this study, we identified 41 KUP/HAK/KT genes (PeHAKs) distributed across 18 chromosomal scaffolds of the Moso bamboo genome. PeHAK is a typical membrane protein with a conserved structural domain and motifs. Phylogenetic tree analysis classified PeHAKs into four distinct clusters, while collinearity analysis revealed gene duplications resulting from purifying selection, including both tandem and segmental duplications. Enrichment analysis of promoter cis-acting elements suggested their plausible role in abiotic stress response and hormone induction. Transcriptomic data and STEM analyses indicated that PeHAKs were involved in tissue and organ development, rapid growth, and responded to different abiotic stress conditions. Subcellular localization analysis demonstrated that PeHAKs are predominantly expressed at the cell membrane. In-situ PCR experiments confirmed that PeHAK was mainly expressed in the lateral root primordia. Furthermore, the involvement of PeHAKs in potassium ion transport was confirmed by studying the potassium ion transport properties of a yeast mutant. Additionally, through homology modeling, we revealed the structural properties of HAK as a transmembrane protein associated with potassium ion transport. This research provides a solid basis for understanding the classification, characterization, and functional analysis of the PeHAK family in Moso bamboo.

Silver nanoparticle-induced in vitro flowering in Dendrocalamus strictus (Roxb.) nees and genetic fidelity assessment of regenerants using molecular markers.

BACKGROUND: Dendrocalamus strictus (Roxb.) Nees, generally referred to as 'Male bamboo,' is a globally prevalent and highly significant species of bamboo. It is a versatile species and possesses notable industrial significance. However, despite its numerous applications, the production of this plant is insufficient to fulfill the worldwide demand. The challenges that impede the dissemination of D. strictus encompass the unpredictable blooming pattern (30-70 years), low seed production, and limited seed viability. Therefore, tissue culture presents a reliable and effective option for the mass production of standardized planting material. METHODOLOGY AND RESULTS: This study investigated the effects of silver nanoparticles (AgNPs) at a concentration of 6.0 mg L- 1 in the Murashige and Skoog (MS) nutrient medium fortified with pre-optimized plant growth regulators (3.0 mg L- 1 6-benzylaminopurine + 0.5 mg L- 1 α-naphthalene acetic acid) on the induction of flowering in a controlled environment in D. strictus. The use of AgNPs in the media induced a maximum of 14 inflorescences per culture vessel, 9 flowers per inflorescence, and improved the performance of the micropropagated plantlets during acclimatization in the greenhouse and field. The ISSR and SCoT amplified polymorphic DNA analysis of the regenerants resulted in the formation of 49 bands (300 to 2000 bp size) and 36 scorable bands (350 to 2000 bp) respectively. All the PCR amplicons produced by SCoT and ISSR were monomorphic confirming the genetic uniformity of the tissue cultured plants of D. strictus with the mother plant. CONCLUSIONS: It can be inferred that the incorporation of AgNPs during the shoot proliferation phase has the potential to stimulate in vitro flowering in D. strictus. This finding could provide valuable insights into innovative strategies for enhancing crop productivity and genetic manipulation for accelerated breeding and agricultural advancement.

Unveiling the Dissolution Regularities of the Lignin-Carbohydrate Complex in Bamboo Cell Walls during Alkali Pretreatment.

Bamboo is a promising biomass resource. However, the complex multilayered structure and chemical composition of bamboo cell walls create a unique anti-depolymerization barrier, which increases the difficulty of separation and utilization of bamboo. In this study, the relationship between the connections of lignin-carbohydrate complexes (LCCs) within bamboo cell walls and their multilayered structural compositions was investigated. The chemical composition, structural properties, dissolution processes, and migration mechanisms of LCCs were analyzed. Alkali-stabilized LCC bonds were found to be predominantly characterized by phenyl glycoside (PhGlc) bonds along with numerous p-coumaric acid (PCA) linkage structures. As demonstrated by the NMR and CLSM results, the dissolution of the LCC during the alkaline pretreatment process was observed to migrate from the inner secondary wall (S-layer) of the bamboo fiber cell walls to the cell corner middle lamella (CCML) and compound middle lamella (CML), ultimately leading to its release from the bamboo. Furthermore, the presence of H-type lignin-FA-arabinoxylan linkage structures within the bamboo LCC was identified with their primary dissolution observed in the S-layer of the bamboo fiber cell walls. The study results provided a clear target for breaking down the anti-depolymerization barrier in bamboo, signifying a major advancement in achieving the comprehensive separation of bamboo components.

Characterization and safety assessment of bamboo shoot shell cellulose nanofiber: Prepared by acidolysis combined with dynamic high-pressure microfluidization.

The preparation of cellulose nanofiber (CNF) using traditional methods is currently facing challenges due to concerns regarding environmental pollution and safety. Herein, a novel CNF was obtained from bamboo shoot shell (BSS) by low-concentration acid and dynamic high-pressure microfluidization (DHPM) treatment. The resulting CNF was then characterized, followed by in vitro and in vivo safety assessments. Compared to insoluble dietary fiber (IDF), the diameters of HIDF (IDF after low-concentration acid hydrolysis) and CNF were significantly decreased to 167.13 nm and 70.97 nm, respectively. Meanwhile, HIDF and CNF showed a higher crystallinity index (71.32 % and 74.35 %). Structural analysis results indicated the successful removal of lignin and hemicellulose of HIDF and CNF, with CNF demonstrating improved thermostability. In vitro, a high dose of CNF (1500 µg/mL) did not show any signs of cytotoxicity on Caco-2 cells. In vivo, no death was observed in the experimental mice, and there was no significant difference between CNF (1000 mg/kg·bw) and control group in hematological index and histopathological analysis. Overall, this study presents an environmentally friendly method for preparing CNF from BSS while providing evidence regarding its safety through in vitro and in vivo assessments, laying the foundation for its potential application in food.

Effect of Plasma Treatment on Bamboo Fiber-Reinforced Epoxy Composites.

Bamboo cellulose fiber (BF)-reinforced epoxy (EP) composites were fabricated with BF subjected to plasma treatment using argon (Ar), oxygen (O2), and nitrogen (N2) gases. Optimal mechanical properties of the EP/BF composites were achieved with BFs subjected to 30 min of plasma treatment using Ar. This is because Ar gas improved the plasma electron density, surface polarity, and BF roughness. Flexural strength and flexural modulus increased with O2 plasma treatment. Scanning electron microscopy images showed that the etching of the fiber surface with Ar gas improved interfacial adhesion. The water contact angle and surface tension of the EP/BF composite improved after 10 min of Ar treatment, owing to the compatibility between the BFs and the EP matrix. The Fourier transform infrared spectroscopy results confirmed a reduction in lignin after treatment and the formation of new peaks at 1736 cm-1, which indicated a reaction between epoxy groups of the EP and carbon in the BF backbone. This reaction improved the compatibility, mechanical properties, and water resistance of the composites.

The Impact of Phenological Gaps on Leaf Characteristics and Foliage Dynamics of an Understory Dwarf Bamboo, Sasa kurilensis.

Phenological gaps exert a significant influence on the growth of dwarf bamboos. However, how dwarf bamboos respond to and exploit these phenological gaps remain enigmatic. The light environment, soil nutrients, leaf morphology, maximum photosynthetic rate, foliage dynamics, and branching characteristics of Sasa kurilensis were examined under the canopies of Fagus crenata and Magnolia obovata. The goal was to elucidate the adaptive responses of S. kurilensis to phenological gaps in the forest understory. The findings suggest that phenological gaps under an M. obovata canopy augment the available biomass of S. kurilensis, enhancing leaf area, leaf thickness, and carbon content per unit area. However, these gaps do not appreciably influence the maximum photosynthetic rate, total leaf number, leaf lifespan, branch number, and average branch length. These findings underscore the significant impact of annually recurring phenological gaps on various aspects of S. kurilensis growth, such as its aboveground biomass, leaf morphology, and leaf biochemical characteristics. It appears that leaf morphology is a pivotal trait in the response of S. kurilensis to phenological gaps. Given the potential ubiquity of the influence of phenological gaps on dwarf bamboos across most deciduous broadleaf forests, this canopy phenomenon should not be overlooked.

Full phenology cycle carbon flux dynamics and driving mechanism of Moso bamboo forest.

Introduction: Moso bamboo forests, widely distributed in subtropical regions, are increasingly valued for their strong carbon sequestration capacity. However, the carbon flux variations and the driving mechanisms of Moso bamboo forest ecosystems of each phenology period have not been adequately explained. Methods: Hence, this study utilizes comprehensive observational data from a Moso bamboo forest eddy covariance observation for the full phenological cycle (2011-2015), fitting a light response equation to elucidate the evolving dynamics of carbon fluxes and photosynthetic characteristics throughout the entire phenological cycle, and employing correlation and path analysis to reveal the response mechanisms of carbon fluxes to both biotic and abiotic factors. Results: The results showed that, First, the net ecosystem exchange (NEE) of Moso bamboo forest exhibits significant variations across six phenological periods, with LSOFF demonstrating the highest NEE at -23.85 ± 12.61 gC·m-2·5day-1, followed by LSON at -19.04 ± 11.77 gC·m-2·5day-1 and FGON at -17.30 ± 9.58 gC·m-2·5day-1, while NFOFF have the lowest value with 3.37 ± 8.24 gC·m-2·5day-1. Second, the maximum net photosynthetic rate (Pmax) and apparent quantum efficiency (α) fluctuated from 0.42 ± 0.20 (FGON) to 0.75 ± 0.24 mg·m-2·s-1 (NFOFF) and from 2.3 ± 1.3 (NFOFF) to 3.3 ± 1.8 µg·µmol-1 (LSOFF), respectively. Third, based on the path analysis, soil temperature was the most important driving factor of photosynthetic rate and NEE variation, with path coefficient 0.81 and 0.55, respectively, followed by leaf area index (LAI), air temperature, and vapor pressure difference, and precipitation. Finally, interannually, increased LAI demonstrated the potential to enhance the carbon sequestration capability of Moso bamboo forests, particularly in off-years, with the highest correlation coefficient with NEE (-0.59) among the six factors. Discussion: The results provide a scientific basis for carbon sink assessment of Moso bamboo forests and provide a reference for developing Moso bamboo forest management strategies.

In situ retention of lignin-rich bamboo green effectively improves the surface properties of flattened bamboo.

Bamboo has tremendous carbon sequestration potential, and bamboo green is underutilized. This work devised a green-keeping technique in bamboo flattening that preserved natural bamboo green in-situ. The impacts of flattening and green-keeping on bamboo morphology, chemical composition, physical qualities, and composite applications were examined. Bamboo cells were wrinkled after flattening, while bamboo green exhibited a more homogenous surface. Bamboo cellulose crystallinity increased after flattening, hemicellulose deteriorated little, and relative lignin content increased. The hydrophobicity and mildew resistance of the surface of G-FB (green-kept flattened bamboo board) were improved. Compared to untreated bamboo, FB and G-FB had 61.1 % and 49.5 % higher tensile strength and 8.0 % and 33.2 % higher MOR. G-FB-made flooring exhibited a MOR of 134.7 MPa and upgraded surface properties. Bamboo green preservation boosted utilization of materials and improved flattened bamboo's exterior surface without affecting lamination bonding. Simple bamboo green preservation multifunctionalizes flattened bamboo composites.

Effect of Deashing Treatment on Ash Fusion Characteristics of Biochar from Bamboo Shoot Shells.

To investigate the influence of deashing on fusion characteristics, a combined method of water and acid washing with different sequences (water washing followed by acid washing, and acid washing followed by water washing) was used to treat the biochar of bamboo shoot shells (BBSSs). The results show that deashing decreased the K content of the biochar from 50.3% to 1.08% but increased the Si content from 33.48% to 89.15%. The formation of silicates and aluminosilicates from alkali metal oxides with silicon was an inevitable result of ash phase transformation at the high temperatures used to improve the fusion temperature (>1450 °C). The thermochemical behavior of ash mainly occurs at 1000 °C. The deashing treatment significantly reduced the reaction intensity during the high-temperature process. This significantly increased the thermal stability of the ash. The adjustment of the washing sequence had a slight impact on the chemical compositions, but the differences in ash micromorphology were obvious. Deashing treatments with different washing sequences can significantly improve ash fusion properties effectively and reduce the risk of scaling, slagging, and corrosion. This study provides a new and reasonable strategy for the deashing of biochar to commercially utilize bamboo shoot shell resources.

Mechanical and Fire Properties of Flame-Retardant Laminated Bamboo Lumber Glued with Phenol Formaldehyde and Melamine Urea Formaldehyde Adhesives.

This study investigated the effects of different adhesives, phenol formaldehyde (PF) and melamine urea formaldehyde (MUF), on the mechanical and fire properties of flame-retardant laminated bamboo lumber (LBL). The results demonstrated that the flame-retardant treatment using phosphorus-nitrogen-boron compounds endowed the LBL with excellent flame retardancy and smoke suppression properties, even though the bending strength and bond shear strength were slightly reduced. The PF-glued LBL exhibited superior mechanical and shear properties to the MUF-glued ones, primarily due to its higher processing temperature and deeper adhesive penetration. In addition, the MUF-glued flame-retardant LBL displayed better heat release reduction and smoke suppression properties than the PF-glued LBL, which resulted from the synergistic flame retardancy between the melamine element in MUF and the applied flame retardant. The analysis of the influence of adhesive type on the mechanical and fire properties of flame-retardant LBL holds significant importance for the future design and production of high-performance LBL material.

Effect of Resin Content on the Structure, Water Resistance and Mechanical Properties of High-Density Bamboo Scrimbers.

Bamboo scrimber is acknowledged for its eco-friendly potential as a structural material. Its properties are significantly affected by both its density and resin content, but the effect of resin content on the properties under high density is not yet known. In this study, the microstructure, water resistance, mechanical properties, and thermal stability of bamboo scrimbers with varying resin content at a density of 1.30 g/cm3 were investigated. The results unearthed that phenolic resin assisted in the densification of bamboo cells during hot pressing, and a higher resin content could effectively reduce the cracks in the scrimber. The inherent cellulose I structure remained unaffected, but an increase in resin content led to a noticeable decline in crystallinity. Additionally, an increase in resin content pronouncedly improved the water resistance and dimensional stability of bamboo scrimbers. The water absorption and thickness swelling were as low as 9.67% and 7.62%, respectively. The modulus of rupture (MOR) exhibited a marginal increase with the amount of resin, whereas the compressive strength and short-beam shearing strength first increased and then decreased. Their peak strengths were 327.87 MPa at a resin content of 15 wt.%, and 168.85 MPa and 25.96 MPa at 11 wt.%, respectively. However, phenolic resin accelerated the thermal decomposition of bamboo scrimbers, and more resin worsened the thermal stability. These research outcomes offer a dual advantage, providing both a theoretical foundation and concrete data that can inform the production and practical application of high-density bamboo scrimbers.

Eco-friendly flame-retardant bamboo fiber/polypropylene composite based on the immobilization of halloysite nanotubes by tannic acid-Fe3+ complex.

Bamboo fibers (BF), as an important sustainable natural material, are becoming a hot alternative to synthetic fibers for the reinforcement of polypropylene (PP)-based composites. However, the weak interfacial compatibility between BF and PP as matrix and their inherent flammability limit the practical application of BF/PP composites (BPC). Here, a fire-safe BPC was fabricated by constructing flame-retardant interfacial layers containing tannic acid (TA)-Fe3+ complex and halloysite nanotubes (HNTs) on the fiber matrix followed by a hot-pressing process. The results showed that the interfacial chelating of TA with Fe3+ improved the dispersion of HNTs on the fibers and the interfacial interactions within the fiber matrix, resulting in the as-fabricated composite with significantly improved mechanical properties and water resistance. In addition, the flame-retardant composite exhibited higher thermal stability and enhanced residual char content. Moreover, the composite possessed significant flame-retardant performances with a reduction of 23.75 % in the total heat release and 32.44 % in the total smoke production, respectively, owing to the flame retarding in gaseous phase and condensed phase of TA-Fe3+@HNTs layers. This work offers a green and eco-friendly strategy to address the inherent problems of BPC material in terms of fire safety and interfacial compatibility, thus broadening their applications in the automotive interior and construction industries.

Efficient fabrication of anisotropic regenerated cellulose films from bamboo via a facile wet extrusion strategy.

Bamboo, featuring fast growth rate and high cellulose content, is considered to be one of the most attractive feedstocks for degradable bio-materials as a substitute for plastics. However, those was limited to the fields of bamboo structural materials mainly by physical processes. Herein, we report a facile continuous wet extrusion strategy for scalable manufacturing of anisotropic regenerated cellulose films in alkali/urea aqueous solution for the first time. The bamboo cellulose solution was regenerated in H2SO4/Na2SO4/ZnSO4 aqueous solution to facilitate the construction of dense fibrils networks. Moreover, under the synergistic effect of shear orientations and stretching processes in wet extrusion molding, the cellulose networks promoted further orientated assembly into aligned fibrils. Therefore, these anisotropic cellulose hydrogels exhibited good mechanical properties, and the tensile strength was increased from 1.67 MPa of anisotropic cellulose hydrogel with 1.0 of stretching ration (ACH-1.0) to 2.13 MPa of ACH-1.4 with increasing stretching ratio from 1.0 to 1.4, which was about 1.34 times higher than that of the isotropic hydrogel fabricated by tape-casting. Moreover, ACH-1.4 exhibited commendable thermal stability and air barrier properties. This work demonstrated a simple and continuous bottom-up approach for fabrication of anisotropic bamboo-based cellulose hydrogels and films with excellent mechanical properties.